Enter your search terms
Submit search form
Web
examineonline.googlepages.com
Online Exam
>>
CISCO
>>
CCNA
>>
Test 6
Menu
Programming
COMPTIA
GMAT
English
IQ
DataBase
OS
MCSE
CISCO
Finance
Management
Health
Soft Skills
Web Building
Multimedia
Test 6
1 . What would be the proper command to set a DCE clock rate of 56k for a serial interface?
A.
Router# clockrate 56000.
B.
Router (config-if) # clockrate 56k
C.
Router (config) # clockrate 56000
D.
Router (config-if) #clock rate 56000
2 . A Telnet session to a remote host would be addressed to what port number at the remote host?
A.
TCP port 23
B.
TCP port 53
C.
TCP port 21
D.
UDP port 21
E.
UDP port 53
3 . What would the class and major network be for the IP address 191.12.45.254?
A.
Class C, 191.12.45.0
B.
Class B, 191.12.45.0
C.
Class B, 191.12.0.0
D.
Class C, 191.12.0.0
4 . What is the result of the command?
" access-list 101 permit tcp any 172.16.0.0 0.0.255.255 established"
A.
telnet sessions will be permitted regardless of the source address
B.
telnet sessions will be denied regardless of the source address
C.
telnet sessions will be permitted to the 172.16.0.0 network only
D.
telnet sessions will be denied if initiated from any address other than 172.16.0.0 network
5 . TCP "source" port number(s): (Choose the one that best describes.)
A.
Depends on the application being accessed on the destination host.
B.
Depends on the application running on the source host.
C.
Are usually assigned by the source host, and are typically some number greater than 1023.
D.
Are assigned by the source host and are usually one of the "well known" port numbers.
6 . The line console 0 command could be used to:
A.
Establish a telnet session with a remote router.
B.
Set a login password for an incoming telnet session.
C.
Set a login password on the console terminal.
D.
Set a password to restrict access to privileged EXEC mode.
7 . Which protocols are best described as connection-oriented and reliable? (Choose two.)
A.
UDP over IP
B.
TCP over IP
C.
TCP
D.
IPX
8 . In a TCP acknowledgment, the ack number refers to:
A.
The number of the packet expected next, plus 1
B.
A sequential number beginning with 1, and incremented by 1 with each exchange, that identifies this exchange of packets as being complete
C.
The number of the packet expected next
D.
A number agreed upon at session establishment, which will be used by the receiver to indicate a successful exchange of packets
9 . The size of a window in a TCP segment establishes what? (Choose one.)
A.
The number of 32-bit words in the header
B.
The number of octets that the receiver must be willing to accept
C.
The number of octets that the sender is willing to accept
D.
The allowable bandwidth for this TCP session
10 . Which one of the following is true as it pertains to IPX RIP Load Balancing?
A.
The parallel paths must have the same tick count and the same hop count.
B.
The parallel paths must have the same hop count.
C.
The parallel paths must have the same band width.
D.
The parallel paths must have the same clock rate.
11 . Given the IPX address 4a.0002.1111.a999, what is the network ID and what is the node ID?
A.
net 4a host 0002.1111.a999
B.
net 0002.1111 node a999
C.
net 0002.1111.a999 node 4a
D.
net a999 node 0002.1111
12 . Identify the command to run 'setup'
A.
Router?setup
B.
Router#setup
C.
Router>setup
D.
Router(config)#setup
13 . How do you disable advanced editing?
A.
terminal no editing
B.
disable editing
C.
terminal editing
D.
no terminal editing
14 . Identify the command that configures serial0 for PPP encapsulation?
A.
Router(config)# encapsulation ppp
B.
Router# encapsulation ppp
C.
Router(config-if)# encapsulation ppp
D.
Router(config-if)# encapsulation serial ppp
15 . What is the syntax to use to configure the port on a Catalyst 5000 switch?
A.
type slot/port
B.
slot port/type
C.
port type/slot
D.
port slot/type
Test Name :
Test 6
Category :
CCNA
Number of Question :
15
Pass Score :
80
Test Result
Your Score :
Passing Score :
80
Result :
Copyright by
VanTuMinh
© 2007
